EPP vs EVA vs PU Foam: A Soft Play Materials Decision List
Two foam suppliers publish data for what looks like the same product. One lists an EVA sheet range of 30 to 200 kg/m³. The other lists 24 to 180 kg/m³ for the same family of material. Neither range is wrong, and neither tells you which block will still be standing at the end of season two.
Soft play foam is the least inspected material in an indoor park. Buyers check steel gauges, bed counts and certificate folders, then accept the foam inside the vinyl as a bundled line item. The failure usually shows up later: cubes that stay compressed after a landing, step blocks that lose height, edges that go from round to sharp. None of this appears on a delivery day inspection.
This article organizes the material decision the way a buyer actually meets it, in this order: the foam pit, the floor layer, the molded blocks, the vinyl cover, then the fire paperwork. Every number below comes from a published source, and every place where the sources disagree is marked, because that is where the real decision lives.
1. Four Materials, Four Jobs in One Park
A trampoline park or soft play center uses four foam-family materials at once. They are not substitutes for each other, and comparing them head to head is the first mistake. Each one answers a different load case.
| Material | Where it appears | Published density range | Cell structure | Source of range |
|---|---|---|---|---|
| Polyurethane (PU), open-cell | Foam pit cubes, crash padding cores | 1.8 lb/ft³ (about 29 kg/m³) is the trade default | Open, breathes on impact | FoamOrder and FoamTouch product pages |
| EVA, cross-linked sheet | Floor mats, step blocks, thin padding layers | 24–200 kg/m³ across two supplier datasheets | Closed cell | Parkway Foam and Guanshan datasheets |
| EPP, molded bead foam | High-traffic blocks, impact edges, modular shapes | 20–90 g/L (= 20–90 kg/m³) in JSP grade table | Closed cell, beaded | JSP ARPRO physical properties sheet |
| PVC-coated polyester (vinyl) | Covers over every foam core | 610 g/m² (18 oz) trade baseline, 1000D scrim | Not a foam; a textile | Tarpaulin supplier technical pages |
Three of these rows use density as the headline number, but they measure it under different test methods, and that detail drives most of the confusion in quotes. The sections below take each material in the order a buyer should decide it, not the order a catalog lists it.
2. Foam Pit Cubes: Why 1.8 Pounds Became the Default
Ask three pit foam suppliers in the United States what they sell and the answer converges: 1.8 lb/ft³ polyurethane, cut into 6 inch (152 mm) cubes. FoamOrder states it directly: 1.8 lb/ft³ white PU, 6 by 6 by 6 inch cubes, with a 3 to 5 year life under daily pit use. FoamTouch sells the same density with an indentation load deflection (ILD) of 44 lb and a stated life of 5 to 7 years.
The conversion matters for cross-border quotes. One pound per cubic foot is 16.02 kg/m³, so 1.8 lb/ft³ converts to about 29 kg/m³. When a supplier outside the United States quotes a cube “density 28 to 30”, check which unit they mean before comparing prices, because a 28 to 30 kg/m³ cube and a 28 to 30 lb/ft³ cube are different products by a factor of sixteen.
What it decides Cube density is the ratio between the weight of the foam and the air inside it. Low-density cubes deform easily and feel soft, which protects a six-year-old but packs down fast under adults. Higher density costs more per cube and adds weight to every shipping carton. The 1.8 lb default exists because it sits at the point where most parks found the trade acceptable, not because a standard mandates it.
What to verify Two suppliers publish different service lives for the same density: 3 to 5 years and 5 to 7 years. Both are self-declared. The property that predicts your replacement date is the compression set, and density itself is measurable on site with a scale and a ruler (Section 7).
Cube quantity is pure arithmetic, which makes it the one place a quote can be checked without any lab:
cubes needed ≈ pit volume (m³) × 282 for 152 mm cubes 282 = 1 ÷ (0.1524 m)³, no packing allowance refill cost ≈ cubes × unit price + freight + closed days × lost sessions
The arithmetic above is the result: a quote that skips the packing allowance will under-count by a few percent, and a quote that forgets freight and downtime will under-count by much more. Get the refill date wrong by two years and you pay for the cubes, the freight and the closure twice.
3. EVA Sheets: Where the Two Datasheets Disagree
EVA (ethylene-vinyl acetate) is the closed-cell sheet foam under play surfaces and inside step blocks and thin padding layers. It is also the clearest example of why datasheet reading is a skill.
Parkway Foam, a manufacturer operating since 2001, publishes a range of 30 to 200 kg/m³ with hardness from 20 to 80 Shore C. Guanshan Industry, another closed-cell EVA manufacturer, publishes 24 to 180 kg/m³ with hardness from 17 to 50 Shore C, graded S30 through S65. Both describe the same material family. The ranges overlap but they are not the same, and neither page claims to be a specification limit.
| Property | Parkway Foam datasheet | Guanshan datasheet | What it changes on site |
|---|---|---|---|
| Density | 30–200 kg/m³ | 24–180 kg/m³ | Step feel and dent resistance |
| Hardness | 20–80 Shore C | 17–50 Shore C | Whether a landing deck reads as soft or firm |
| Water absorption | 0.04% | max 5–10% | Cleaning regime near wet zones |
| Compression set (25%) | listed as 190 (unit unstated) | 0.5–6% at 70°C × 22 h | Whether the block keeps its height |
| Flame rating | anti-fire grade offered | EN 13501-1 class D and E (≥3 mm sheets) | Paperwork per market |
Read that table twice. The water absorption rows differ by two orders of magnitude, and the compression set row is the reason this article exists: one supplier leaves the unit unstated, the other tests at 70°C for 22 hours under 25% compression. These are different test conditions, so the numbers are not comparable across the two pages, and a buyer who forwards one number to a second supplier will get a quote for a different material.
What it decides For floor mats, the useful question is not “what is your density” but “what is your density and hardness at the thickness I am buying, tested under which method”. A 45 kg/m³ sheet at 50 Shore C and a 45 kg/m³ sheet at 25 Shore C are both legitimate EVA products that behave nothing alike underfoot.
What to verify Ask the supplier to state, in one line per property: the value, the test method and the test condition. If any of the three is missing, the number is a marketing claim, not a property. This is the same verification discipline used in a supplier audit (see our eight-check deposit list, linked below).
4. EPP Blocks: What Each Density Grade Buys
EPP (expanded polypropylene) is the molded bead foam you meet in high-traffic impact zones and modular block systems. Unlike PU and EVA, EPP is published in a proper grade table by a resin-scale manufacturer. JSP, the maker of ARPRO EPP, lists seven grades from 20 to 90 g/L (identical to kg/m³) tested under ASTM D3575.
The grade table rewards reading past the density column. Compressive strength at 25% strain rises from 0.09 MPa at 20 g/L to 0.39 MPa at 60 g/L and 0.65 MPa at 90 g/L. In other words, doubling the grade from 30 to 60 more than doubles the load the block carries before it deforms a set amount. Tear strength rises from 1.74 to 4.35 kN/m across the same range. Compression set stays at 10 to 14% across all grades, which is the property that lets an EPP edge take repeated hits and return to shape.
What it decides EPP is not automatically “better” than EVA or PU. It recovers from multi-impact better than most alternatives, it does not absorb water, and it molds into shapes that sheet foam cannot hold. It is also stiffer per unit of softness: an EPP block at a given density feels harder than a PU block at the same number, because the cell structures differ. For toddler zones that softness is the point; for a landing edge behind a slide, the EPP recovery is the point.
What to verify The JSP sheet carries an honest warning: values are typical and “should not be construed as specification limits”. A molder can process the same resin into a part with different fusion quality, so the block-level question is whether the molded part, not the resin, meets the grade. Ask for the molded-part test, not the resin datasheet.
5. The Vinyl Cover: 18 oz Is a Baseline, Not a Guarantee
Every core above hides behind a PVC-coated polyester cover. The trade baseline is 610 g/m², sold in the United States as 18 oz vinyl. Tarpaulin suppliers publish matching detail on what that weight contains: a 1000D by 1300D polyester scrim (one lists 840D by 840D), tensile strength from about 2,000 N/5cm up to 2,500/2,300 N/5cm warp and weft, tear strength of 220 to 450 N, and coating adhesion around 100 N/5cm.
Two lessons hide in those numbers. First, “18 oz” fixes the total weight but not the weave: two 610 g/m² fabrics with different deniers and thread counts will wear differently at seams and step edges, and the heavier scrim is what resists the zipper-style seam failures suppliers describe. Second, weight says nothing about the chemistry: the same supplier sells 610 g/m² fabric in phthalate-free REACH-compliant grades and in standard grades, and only the former is appropriate where children mouth surfaces.
What it decides The cover takes the abrasion, the cleaning chemicals and the UV near windows. Most “foam problems” reported by park staff are cover problems: a seam let go, the coating stiffened, or the print cracked and exposed the foam. The cover is also the only part an operator can inspect visually every day, which is why the replacement decision should be made per panel, not per park.
What to verify Ask for the scrim construction (denier and threads per inch) and the adhesion value, not just the weight. 610 g/m² with a weak scrim is a heavier version of a worse fabric.
6. Fire Paperwork by Market: Ask for Numbers, Do Not Memorize Them
Flammability is where soft play materials get tangled, because three regulatory systems overlap and none of them was written for foam blocks. The practical move is to know which document applies in which market, and to demand the matching test report by number.
- United States, toys and children’s products: 16 CFR 1500.44 (under the Federal Hazardous Substances Act) bans items classed as extremely flammable solids. It is a ban on the worst performers, not a grading system.
- United States, play equipment: ASTM F1918 covers soft contained play equipment. It governs the equipment design and performance; it does not hand the buyer a foam-density number.
- European Union, toys: EN 71-2 covers flammability of toys. A commercial soft play block built for a venue is generally not sold as a toy, so EN 71-2 applies to toy-grade products, and a certificate for one category does not transfer to the other.
- United Kingdom, foam-filled contract furniture: BS 5852 sets ignition-resistance tests for upholstered furniture covering materials, and “crib 5” (the medium-hazard source) is the level UK venue procurement commonly specifies for foam-filled items. Park buyers in other markets often import this spec voluntarily.
- Building-level rules: the fabric suppliers above offer NFPA 701 and DIN 4102 B1 grades. These are fabric and construction tests; they sit on top of, not instead of, the product rules above.
The rule for a buyer is simple: for each foam-filled item, ask which standard the supplier claims, for which scope, and request the test report that shows it. What you should never accept is a certificate for a different product category offered as proof for yours. We keep the checklist version of this on our materials and safety pages, and the same discipline applies to any claim a quotation makes.
7. What the Datasheets Still Do Not Tell You
This section is the reason to read past any supplier table, including ours.
No public standard sets a minimum density for soft-play foam cores. The 1.8 lb/ft³ pit cube is a market convention. The EVA and EPP ranges are what suppliers choose to publish. A regulator checks hazards and, where applicable, fire behavior; nobody from outside audits whether the block you bought matches the density stated on the invoice.
Datasheet numbers are not comparable across suppliers. The two EVA pages above test compression set under different conditions. The JSP sheet tests resin under ASTM D3575 while your block is a molded part. A spreadsheet that sorts suppliers by a single density column is comparing numbers that were not measured the same way.
There is a field check, and it is arithmetic. Density is mass divided by volume. Cut or borrow a clean block, weigh it, measure it, divide:
density (kg/m³) = mass (kg) ÷ volume (m³) a 152 mm PU cube at 1.8 lb/ft³ should weigh ≈ 0.10 kg if it weighs 0.06 kg, the cube is closer to 17 kg/m³, whatever the quote says
The cube weight above is derived from the published density using the same conversion shown in Section 2; it is our arithmetic, not a supplier claim. Weigh three cubes from three cartons. This costs five minutes and catches more substitution than any certificate folder, because certificates describe the batch that was tested, not necessarily the container that was shipped.
What we cannot tell you: how a given density behaves in your park depends on your visitor mix, session lengths and cleaning regime, and no published source models that. The honest position is to fix the density after a stated test method and to buy replacement panels from the same batch records, not to hunt for a magic number.
8. Judgment Table: Which Foam Where
| If your application is… | Choose | Published anchor | Verify before deposit |
|---|---|---|---|
| Foam pit fill, mixed ages | PU open-cell cubes | 1.8 lb/ft³ (about 29 kg/m³), ILD 44 lb | Weigh-sample cubes; confirm count with packing allowance |
| Floor mats and landing decks | EVA sheet | 30–200 kg/m³, 20–80 Shore C (supplier range) | Value + test method + condition in one line |
| Step blocks and toddler shapes | EVA or PU, softer grade | Lower end of each published range | Hardness at purchased thickness |
| High-traffic impact edges, modular blocks | EPP | 60 g/L grade: 0.39 MPa at 25% strain, 10–14% set | Molded-part test, not resin datasheet |
| Every cover, all of the above | PVC-coated polyester | 610 g/m², 1000D-class scrim, adhesion about 100 N/5cm | Scrim construction + phthalate grade |
| Any item in a UK venue with foam fill | Cover + foam to BS 5852 crib 5 practice | Ignition-resistance test by source level | Test report naming the standard and source |
Replacement math closes the loop. A pit refilled two years early costs the cube price again plus freight plus the closed days, and the same logic applies to step blocks that went flat. The material premium that prevents one early refill usually pays for the whole difference, which is why the verification steps above cost nothing and skip nothing.
9. Summary and Three Checks Before You Pay a Deposit
The four materials in a park divide cleanly by job: PU for pits, EVA for surfaces and steps, EPP for repeated-impact edges, vinyl over all of it. Each has a published anchor value, and none has a regulator-set density floor, so the verification burden sits with the buyer. The datasheets disagree with each other in ranges and in test conditions, and that disagreement is information: it tells you exactly which questions a supplier must answer in writing.
1. Demand one-line properties. Value, test method, test condition, for every foam and fabric on the quote. A number without a method is a claim.
2. Weigh three cubes. The density formula in Section 7 is the only materials lab that cannot lie. Do it on delivery day, before the invoice clears.
3. Match certificates to scope. A toy flammability report does not cover a venue block; a fabric rating does not cover the foam. If you want a second pair of eyes on a quote before the deposit, send it to our team for a materials review.
FAQ
What density foam is used in a trampoline park foam pit?
The trade default in the United States is 1.8 lb/ft³ polyurethane, which converts to about 29 kg/m³, typically cut into 6 inch (152 mm) cubes. Two suppliers pair that density with an ILD of 44 lb and state service lives of 3 to 5 and 5 to 7 years respectively under daily use.
Is EPP better than EVA for soft play blocks?
Neither is universally better. EPP recovers from repeated impacts and does not absorb water; JSP publishes 10 to 14% compression set across its 20 to 90 g/L grades. EVA sheet is easier to fabricate into mats and step blocks, and its published ranges span 24 to 200 kg/m³ depending on the supplier. Choose by load case: EVA for surfaces and light blocks, EPP for edges and high-traffic impact zones.
What does 18 oz vinyl mean for play equipment covers?
It is a weight: 18 ounces per square yard, equal to about 610 g/m². The weight alone does not fix quality; the polyester scrim inside it (denier such as 1000D and the thread count) and the coating adhesion (about 100 N/5cm on published datasheets) determine how the cover wears at seams and steps.
Which fire standards apply to soft play foam and covers?
By market: 16 CFR 1500.44 bans extremely flammable solids in the US under the Federal Hazardous Substances Act; ASTM F1918 governs soft contained play equipment design; EN 71-2 covers toy flammability in the EU but does not automatically transfer to venue-built blocks; BS 5852 (crib 5) is the ignition-resistance spec UK venues commonly require for foam-filled contract items; NFPA 701 and DIN 4102 B1 are fabric-level tests offered by cover suppliers. Ask for the test report by number and scope.
How can I check foam density without a lab?
Weigh a block and measure its volume, then divide mass by volume. A 152 mm cube at the standard 1.8 lb/ft³ should weigh about 0.10 kg (our derivation from the published density). If three cubes from three cartons average well below that, the shipment does not match the quote, and you learned it in five minutes instead of two seasons.
Sources
- FoamOrder, “Foam Pit Cubes” (1.8 lb/ft³ PU, 6 inch cubes, 3–5 year life), accessed 10 November 2026 – foamorder.com/foam/foam-pit-foam-1
- FoamTouch, “Foam Pit Block Cubes” (1.8 lb density, ILD 44 lb, 5–7 year life), accessed 10 November 2026 – foamtouch.com/pit-blocks
- Parkway Foam, EVA foam sheet technical data (30–200 kg/m³, Shore C 20–80), accessed 10 November 2026 – parkwayfoam.com/eva-foam-sheet-ld.html
- Guanshan Industry, closed-cell EVA foam sheet specifications (24–180 kg/m³, Shore C 17–50, grade table), accessed 10 November 2026 – guanshanindustry.com
- JSP (ARPRO), Material Physical Properties for Foam, EPP density range 20 to 90 g/L, publication JSP-GenPhysProp-EPP-20to90gl-2018, accessed 10 November 2026 – ARPRO EPP datasheet (PDF)
- UNITARP, 610 gsm (18 oz) PVC-coated tarpaulin for inflatables (1000×1300D scrim, FR options), accessed 10 November 2026 – uni-tarp.com
- ASTM International, ASTM F1918-21, Standard Safety Performance Specification for Soft Contained Play Equipment, scope page, accessed 10 November 2026 – store.astm.org/f1918-21.html
- eCFR, 16 CFR 1500.44, Extremely Flammable Solid Materials (Federal Hazardous Substances Act), accessed 10 November 2026 – ecfr.gov
- Wikipedia, “BS 5852” (ignition-resistance testing for upholstered furniture coverings, crib sources), accessed 10 November 2026 – en.wikipedia.org/wiki/BS_5852
Planning a park build and want the material list specified the same way? See how our design-to-delivery process works or browse our indoor playground equipment and park accessories categories. Related reading: what the five-year maintenance bill looks like and eight supplier checks before you pay a deposit. Our materials and certification practices are summarised on the materials quality page and the safety standards page.
